How to Fix a Dripping Faucet
A dripping faucet can be very annoying. People usually get frustrated by tightening the tap more and more trying to make those little drops to stop appearing again. Mainly, in the end, you would have to call a plumber to fix it for you, which can be irritating too, things can get messy, and of course it would cost you money, which is never pleasant. Is there another way?
You can fix all the dripping faucets yourself. There’s just a few little things that you need to know. You can find a complete guide to getting rid of the dripping faucets in your house here in this article. Dripping faucet fixed

Let’s Get Started
To get started you’d have to make sure to do all of the things described below:

• Cut off the water supply under the sink.
• Clog the drain of the sink. You can use a dirty rag for this purpose.
• Use duct tape to cover the jaws of the wrench that you are about to use to avoid damaging the fixture.
• Make a platform to put all the parts after the disassembly.
• To remove the mineral deposits from the parts of the faucet, use a scouring pad and distilled water vinegar.

Identification of the Faucet
There are 4 types of valves. Yours can be either one of those. There is the ball type, cartridge, compression and the ceramic disk. First of all, you would have to find the kind of faucet you have. After that, you can use the guidance provided below to fix your faucet.
The valve seat is sealed by the rubber washers that a compression faucet has. The thing with rubber washers is that they easily wear out and should regularly be replaced. There is also another type of washerless faucets, they can last a lot longer than the former ones, but they are also prone to developing leaks. When these ceramic disk, cartridge or ball type faucets leak, you can fix them by replacing the O-ring or the neoprene seal. Replacing the entire assembly of the dripping faucets would cost you less than $20.

The Ball Type Faucets
The ball type faucets have a lot of parts. They are often tough to identify in order to find the causative agent that is causing the leak. It can be fixed without all the hustle and bustle by just buying the replacement kit with which you can put all the new parts inside.
First of all, remove the screw of the handle set and lift the handle up to remove it. To remove the cap and the collar you can use pliers. A special tool placed in the replacement kit will help you lose up the faucet cam; this will let you lift the cam washer and the rotating ball along with it.
Use needle nose pliers to reach inside the body of the faucet and remove the springs and seals that are placed inside.
Moving ahead, you are going to have to cut the O-rings off. Use a nontoxic and a heat proof grease that plumbers use on the new O-rings and roll them on very nicely. After that put up the new springs, cam washers, and the valve seats as you move ahead to resemble the faucet. If your faucet is a little too old, it is recommended that you change the entire fixture. To do that you are going to need a basin wrench.

The Compression Faucets

The leakiest of the compression faucets require a change of the seat washers. To start, you are going to have to pry off the decorative cap that is on the handle, after that go ahead and remove the screw, unscrew the packing nut using the crescent wrench after you pull off the handle. After you have removed the stem, you will see a seat washer placed in its position with a brass screw, all you have to do is to replace that with the new one. Use a heat proof and non-toxic plumber’s grease to coat the washers. After that remove the stem, take out the O-ring and replace it with a newer one. O–rings are the main reason of leaky handles.
The O-rings are different in size. Be sure you have the right size of O-ring when applying the new one. Use the plumber’s grease to coat the ring and then reassemble the whole faucet after you have correctly placed the ring.
There are cases in which the faucet continues to leak. If that happens, it is mainly because the seat might be pitted. You would have to use a valve seat dresser to grind and smooth the valve seat. It is a tool that you have to screw down inside the faucet temporarily.

Ceramic-Disk Faucets

To get rid of the leakage here, you would have to disassemble the faucet first. Lift out the neoprene seals using a blunt screwdriver. Check if the seals are broken, if they are you would have to replace them. Clean the cylinder openings using white vinegar (distilled).
Wash it completely, and then replace the seals correctly. After you have replaced the seals go ahead and reassemble the faucet. Turn the faucet to “on” and let the water flow slowly. You have to open the water slowly because the force of water coming in with pressure can damage the ceramic disk.

Cartridge Faucets
Take the cap off of the handle, remove off the screw of the handle, tilt the handle to the side a bit and then pull it off. Use nose pliers to remove a threaded retaining clip that might be holding the cartridge in place. Eliminate the o-rings and take then out after removing the spout. After that take the new O-rings and coat them with the heat proof and non-toxic plumber’s grease. Carefully place the rings back on the place where they were before.
You can replace the entire cartridge of the dripping faucets for less than $10-$15 if you are looking for a longer lasting faucet.

Get to know why your AC is not cooling right
There are times when you get your AC out of order. Particularly, if you are not having its service at regular intervals, you are likely to come across some problem. It will make your electronic device work in an inappropriate manner which will pop a few questions in your mind. You may start thinking that why is your AC not cooling right? What can be the possible problem? How can you overcome the issue and make your device work properly? Well, here we will guide you step by step in diagnosing and eliminating the problem.Air Conditioning repair

Troubleshooting the problem
There are two main types of problems that you may come across when someone talks about AC not working righteously. First of all, there is a chance that the device is not functioning at all. The second possible option can be that the device gets turned on but is not running. Below, we will have a look at potential problems in both cases.

AC not working at all
In case that your AC is not operating, there can be particular problems. First of all, there might be some issue with the power supply. Ensure that the electrical panel with which your item is connected has a proper and active power supply. If the supply is not up to the mark, the machine will not run.

The second possible reason can be the switches with which your device is linked. The switches are designed to bear a certain amount of power. They will not operate if the power supply is lower than the prescribed volts and will be overloaded if the power supply is more than they can bear. In most of the cases, the fuses are attached which gets melt if there is something wrong with the supply.

A common problem that most of the people do not know about is the thermostat settings. You have to set it right in order to make your machine work. If there is something wrong while you are setting it up or you miss a few guidelines while making it work, your AC will not run.

Last but not the least, there is a condensate overflow switch. It will make your device stop working if there is an overflow. Therefore, while you are getting your air conditioner to work 100% for you, make sure that you take a look at the condensate switch and ensure that it is fine in all aspects.

When your AC is running but not cooling
If you are able to turn your AC on successfully, but it is not cooling the way it should be, here are a few things that you can try.

First of all, try turning off the power for a few moments and then turn it on. There are times when your AC is not able to get the right power at the start due to which it is not able to carry out the operation in an efficient manner.

Even if you still have some problem with its cooling, check for the filters. Try cleaning them or cooling them. Most of the time your AC filters get dirty and the dirt is not letting your machine to work the way it should be working. It is one of the most critical points and a reason why many experts recommend the AC service and cleaning on regular intervals.

Last but not the least, there are times when the AC coils have ice on them. The ice is formed which makes your AC unable to work and the cooling efficiency of your machine comes under question. Turning on the fans of your AC will make the ice melt, and this will hopefully get your AC back to its working condition.

There is a condensate drain in your AC. Take a look at the drain. There are times when the drain gets blocked due to a lot of waste. When there is a blockage, your device will not cool righteously. Therefore, clean the drain and then try making your AC work.

The outdoor compressor plays a great role when it comes to cooling. If there is any kind of problem with it, your machine won’t be able to cool your place. Therefore, you need to keep a strict check on the outdoor compressor panel. Check for the waste and clean it at regular intervals in order to get the most from it.

What to do if your AC is not working well?

If your AC is not functioning well, there are two options for you. First of all, get a do it yourself kit and be brave enough to take the responsibility of cleaning your AC on your own. Get your kit and start detaching various parts of your central air-conditioning system. Take a look at the points mentioned above and then check your AC in concern with these to find out where the problem lies. A thorough service of your AC will require appropriate tools which you can get for yourself in the market. However, there are high chances that, if you are not aware of how to open up your AC and detach the parts for cleaning, you will damage a particular element. It will do more harm to you than good, and you will ultimately have to call the experts.

Therefore, if your AC not cooling right, go for the second option which is calling the professional. He will assess your AC system in all possible ways and will try his best to figure out the problem. Once he gets down to the problem, you can be confident that you will have your system working efficiently once the professional clear it. An expert will be able to provide you valuable tips in concern with your AC and will let you know about the do’s and don’ts of operating an AC. So, look up for the experts in your area and give them a call. Many of them provide free consultation and inspection, but conditions may apply.

More here @http://www.hometips.com/repair-fix/central-air-conditioner.html